Skip to content
SoluWeld
  • Beginner
  • Quality

Weld mapping and traceability: from the drawing to the data book

Identify every weld on the drawing and link it to the welder, WPS, materials, inspections and repairs: traceability that stands up to an audit, and a data book built during production rather than after it.

Julien Bachelet · Fondateur · IWE11 November 20265 min read

A radiograph reveals a defect on a delivered weld. Who made it? With which wire batch? Was the welder qualified that day? If it takes you more than ten minutes to answer, your traceability is not good enough.

A weld map turns a drawing into a register: every weld gets an identifier, and everything about it is attached to that identifier.

An identifier does three jobs

  • 1- Proving conformity. A customer, a notified body or an ISO 3834 auditor picks a weld at random and asks you to trace it back: procedure, welder, inspections.
  • 2- Containing a nonconformity. When a defect appears, the identifier leads to the welder, the filler batch, the WPS and the date. You know which other welds to inspect, instead of suspecting the whole project.
  • 3- Running the shop. An up-to-date weld map shows what is welded, inspected, accepted or under repair. It is a progress board, not an archive.

A good identifier is unique within the project, stable when the drawing is revised, and the same on the drawing, the traveller, the inspection report and the final data book. The syntax hardly matters.

What to attach to each weld

InformationThe question it answers
Welder and their WPQ (Welder Performance Qualification)Were they qualified for this process, position and thickness on that date?
WPS (Welding Procedure Specification) and the WPQR that supports itDoes the range of qualification cover this joint?
Base metal: grade, heat number, certificateIs the material welded the one that was planned?
Filler metal: designation, batch numberWhich welds must be isolated if a batch is called into question?
Date, recorded preheat where requiredWere the WPS conditions met?
Visual inspection and NDT (Non-Destructive Testing)Is the weld accepted, against which criterion, by whom?
RepairsIs the final weld compliant after repair?

The WPS, WPQR, WPQ chain is covered in our article on the welding qualification chain. Not every line is required on every job: the contract or the code sets the depth of traceability. ISO 3834 requires it to be maintained demonstrably, to a level that depends on the quality requirement level chosen.

One rule holds everywhere: data not recorded at the time of welding cannot be reconstructed three weeks later.

An inspection rate only means something on a defined population

"10 % RT" means nothing until you say 10 % of what: per welder, per WPS, per joint type, per line? Without a defined population, a welder can go through a whole project without a single weld inspected.

A repair adds to the history, it does not erase it

During a weld repair, most of the original weld usually remains intact. Its history must therefore be kept. Recurring defects for the same welder or the same WPS are quality information. It only shows up if repairs are traced weld by weld.

The data book is built during production

The manufacturing data book gathers what the contract requires: weld list, WPS and WPQR, WPQ, certificates, inspection reports, repairs, sometimes heat treatment and pressure test records.

Building it at the end of the project means chasing scattered documents and finding the gaps when it is too late to fill them. Building it as you go makes it a simple export of each record.

The most common mistakes fit in three lines:

  • the paper form re-keyed in the office, which creates two sources and nobody knows which one is authoritative;
  • the expired or out-of-range WPQ discovered at archiving, once the weld is made and inspected: the check belongs at welder assignment, not afterwards;
  • the filler batch not recorded, which forces you to suspect a whole period instead of a few welds.

What SoluWeld does for you

SoluWeld links each weld identified on the drawing to its welder and WPQ, its WPS and the WPQR that supports it, the materials with heat and batch numbers, visual inspections, NDT and repairs. Joint coverage by the ranges of qualification is checked as soon as the welder is assigned. The weld log and the manufacturing data book build up as production goes. See the welding coordination module, or request a demo on your own drawings.

Evaluate the platform on your real projects.

Thirty minutes on video to measure the time saved on records and the autonomy SoluWeld brings to your teams.